Torch Boosters supply high pressure gas directly to torches and burners
Refuelers let you fill G-TEC cylinders with high pressure natural gas
Natural Gas Cylinders hold 130 cubic feet of natural gas at 275 psi
Purchase a G-TEC Natural Gas Pressure Booster
How To Install your G-TEC System
G-TEC Systems are Approved across the US and Canada
Contact G-TEC if you have questions
Replace propane with a G-TEC Natural Gas Torch Booster for flame plasma surface treatment
Get rid of propane tanks and use a G-TEC Torch Booster to supply high pressure natural gas to flame treat plastic surfaces for printing, painting or adhesion.
​
Natural gas is about 75% cheaper than propane for equal heat
​
Improve workplace safety by getting propane cylinders out of your building
​
Best of all you never run out of gas and don't change empty cylinders.
Natural gas prices are falling and will continue to go down as new technologies increase our national supply. You can rely in cheap, abundant natural gas being readily available!
Fire officials want you to remove propane cylinders - Across the US and Canada fire safety officials are asking businesses to remove propane tanks from buildings because stored gas is a danger if there is a fire or other emergency.
​
One 20 lb propane tank has the energy equivalent of more than 431,000 wooden matches - certain to
make matters worse in a fire. G-TEC Torch Boosters raise city gas pressure and supply gas to your
flame treatment torch as gas is used - Torch Boosters do not store any gas and there is never more
than one cubic foot of gas in the system at any time.
​
Never change cylinders again and never run out of gas! G-TEC Torch Boosters connect to your low
pressure utility natural gas pipe and raise gas pressure as high as 45 psi. Torch Boosters supply high pressure natural gas as it is used and automatically adjust to the gas flow requirement of the burner. There are no storage cylinders and the Booster is ready to work as soon as it is turned on. Never waste productive time changing gas cylinders, never run out of gas in the middle of a job!
G-TEC Torch Boosters for Flame Plasma Surface Treatment
Picking the right Torch Booster is a matter of knowing how much gas you need when all of your systems
are running. Single flame equipment will most likely use a TB-15 or TB-30 Torch Booster, our smaller units.
​
Larger printers with multiple flame treatment systems can fuel them all at one time from a single TB-60
​
Torch Boosters are quiet, compact and can be installed right in the area where high pressure natural gas will be used. No ventilation or other expensive site preparation is required.
​
Torch Boosters are designed to run all day without operator attention - turn the system on in the morning and off at the end of the day and it will automatically adjust to the gas flow your burner uses.
​
Torch Boosters are designed and manufactured to international standards and are welcomed in all buildings in North America. Torch Boosters are CE Compliant for installation in European Union countries. Systems are compatible with both 60 Hz and 50 Hz electric grids.
TB-15 and TB-30 Torch Boosters supply natural gas at either 15 or 40 cubic feet of gas per hour at up to 25 psi. They use 120 V 15 amp electric power and are designed for use in North America.
​
TB-60 and TB-125 Torch Boosters are intermediate size units that supply natural gas at 60 or cubic feet of gas per hour or 125 cubic feet of gas per hour at up to 25 psi and are the right choice to supply several flame treating systems in a large printing facility. These Torch Boosters are available in 120V 60 Hz and 230V 50 Hz models.
​
TB-250 and TB-500 Torch Boosters are high volume systems that provide natural gas at either 300 cubic feet per hour or 500 cubic feet per hour at up to 45 psi. These Torch Boosters are available in 208V 60 Hz and 230V 50 Hz models.
​
Get more information about TB-250 and TB-500 Torch Boosters.
A G-TEC Torch Booster Is Easy To Install In Your Building
G-TEC Torch Boosters do not need any special site preparation such as ventilation - they are quiet and can be placed right in the work area.
​
TB-15, TB-30, TB-60 and TB-125 Torch Boosters come with a flexible 5 foot hose to connect the system to the low pressure utility natural gas pipe. Just install a tee in your building gas pipe, attach the G-TEC provided shutoff valve, screw the hose hose onto each and and you are connected.
​
TB-250 and TB-500 Torch Boosters use a 1 1/2" diameter pipe to make a hard piped connection to the low pressure building gas pipe.
​
Find out more about how a G-TEC Torch Booster will work for you!
​
Call G-TEC at 716-831-9695 / email info@gas-tec.com
Torch Boosters supply high pressure gas directly to torches and burners
Refuelers let you fill G-TEC cylinders with high pressure natural gas
Natural Gas Cylinders hold 130 cubic feet of natural gas at 275 psi
Purchase a G-TEC Natural Gas Pressure Booster
How To Install your G-TEC System
G-TEC Systems are Approved across the US and Canada
Contact G-TEC if you have questions
